Signal Input
Video: 1 balanced loop-through (terminating input option for single width rear panel)

Signal Outputs
Video: Up to 14 unbalanced outputs

Remote Controls:

• Gain: ±4 dB in steps of 0.05 dB

Typical Equalizer Performance
Belden 1694A:

• 0-300m +0.1 dB to 10 MHz
• 0-300m +0.2 dB to 30 MHz

Belden 8281 (PSF1/2):

• 0-300m +0.1 dB to 10 MHz
• 0-300m +0.1 dB; -0.4 dB to 30 MHz

Belden 1855A:

• 0-200m +0.1 dB to 10 MHz
• 200-300m +0.1 dB; -1.5 dB to 10 MHz

RG59B/U:

• 0-100m +0.1 dB to 15 MHz
• 100-300m +0.1 dB; -1.5 dB to 15 MHz

NK 0.6/2.8:

• 0-150m +0.1 dB to 15 MHz
• 0-150m +0.1 dB; -0.5 dB to 30 MHz

AGC: [On/Off] – All recognized SD sources

ACC: [On/Off] – Composite sources only

Signal identification: Line standard – PAL, NTSC, 625 MONO, 525 MONO, 1080p24, 1080i50, 1080i60, 720p50, 720p60, 720p25, 720p30, UNKNOWN

Selectable clamp: Off, On (back porch) and sync tip

Signal level: Sync and burst amplitude ±10%

Logging signal: Level warning, line standard, burst level warning

Indicators
Power: OK

CPU: OK

Status: OK (Green), Warning (Yellow), Error (Red)

Frequency response (without equalization):

• 10 kHz – 10 MHz ± 0.1 dB
• 10 MHz – 30 MHz ± 0.2 dB
• 35 MHz <-1 dB

Differential gain: Unity gain, better than 0.2%

Differential phase: Unity gain, better than 0.2°

Signal/noise ratio: 10 kHz – 7 MHz, better than -66 dB (unweighted)

Linearity: Better than 0.1%

Line tilt : Better than 0.1%

Output D.C.: <90 mV

Output return loss: Better than 40 dB to 5.5 MHz, 35 dB to 30 MHz

Maximum output level: 2.4 Vp-p @ 30 MHz into 75Ω

Insertion delay: 20 ns

Y C gain/ delay inequality: <1%, < 1 ns

K2T, KPB: Better than 0.1%

Max. input level: +6 dB

CMRR: Better than 60 dB at 50 Hz, 40 dB 50 Hz to 8 MHz

Input return loss (powered): Better than 40 dB to 5.5 MHz, 35 dB to 30 MHz

Input return loss (unpowered): Better than 33 dB to 30 MHz

Input impedance: >22 kΩ

Headroom: +6 dB

Output impedance: 75Ω ±1%

Gain: Unity ±1% as supplied

Clamp rejection: 8 dB typical at 50 Hz

Module power consumption:

• 3W Max (A Frames)
• 2 PR (B Frames)

Mechanical
Complies with Restriction of Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive (2002/95/EC).

EMC Performance Information:

• Environment: Commercial and light industrial E2
• Peak mains inrush current following a 5 second mains interruption: No mains input
• Performance information: Immunity to conducted common-mode RF interference (EN 55103 2 immunity phenomenon I6): Interference is just visible on critical picture material when a video input or output is subjected to modulated RF at a level of 3V